EXACTLY HOW TO REMOVE AND REPLACE A BATH TUB.

Exactly How to Remove and Replace a Bath Tub.

Exactly How to Remove and Replace a Bath Tub.

Blog Article

Pest Control Expert

Presented here down the page you'll find more reliable content around A Step-by-Step Guide to Installing a Bathtub.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a tub isn't specifically rocket science, however it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is additionally a moderately challenging job. If the old bathtub is readily available, the job can relocate speedily; if you have to open a wall surface to get rid of the old tub and position the brand-new bathtub, the job is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and set in the brand-new one. See to it you have certified yourself for the job as well as fit attempting it. As opposed to hiring a specialist to take over a halfway-completed project, it is better to think about using one prior to you start. Chances are you might need an expert plumber to make tube links.
This article will assist you set up a new bath tub in your washroom if you have already bought a new tub and also do not require to alter the plan of your previous water pipelines.
Your devices as well as product list should comprise the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome as a result of the limited gain access to that is frequently the instance.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a fabric ready for the remaining water that will originate from the pipelines. When the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
    Before moving on to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.

    Suitable New Taps


    If the tails of the new faucets are plastic, after that you will require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
    If you require to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next off, position the tap in the mounting opening in the bath/basin guaranteeing that the washers are in area in between the tap and also the sink. Protect the faucet in place with the maker provided backnut. When the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The former type needs to be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.

    Mounting the Bathtub


    Utilizing both wooden boards under its feet, position the bathtub in the called for placement. The wood boards are handy in evenly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four small factors.
    The next objective is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also changing the feet on the bath tub until the spirit level reviews degree.
    To install taps, fit all-time low of the furthest versatile faucet connector to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
    Turn on the water and inspect all joints and new pipework for leaks as well as tighten them if essential. Fill up the bath tub and additionally check the overflow outlet and the regular outlet for leakages.
    Lastly, fix the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub ought to wait up until the tub has been utilized a minimum of once as this will settle it into its final setting.

    Getting ready for the Installation


    Firstly, the supporting framework supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to prevent strain on the tub.
    Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
    Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final position.

    Tiling Around the Bath tub


    In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture and also feasible leaks to the ceiling listed below.
    You can choose from a selection of coloured sealants to assimilate your components and installations. They are sold in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can crack relatively early if you do not take into consideration this activity prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly readily available on the market. It is a good idea to fit the tiles using waterproof or waterproof adhesive and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    As an enthusiastic person who reads about How to Install a Bathtub, I think sharing that excerpt was smart. Are you aware of another person who is truly interested in the topic? Feel free to share it. Thanks for going through it.



    Book Instantly

    Report this page